|
HS-004
Hub Spacer - Grant 5 Bolt
|
|
Hub spacers are used when installing a steering wheel mounted trim switch. The spacers are drilled so the trim switch wiring can easily routed to the center of your hub. Rack and Pinion steering systems from Morse and Teleflex can be modified by gun drilling the shaft so the wiring can be routed through the center of the shaft to the back of the dash. When completed, the installation will be very clean with no exposed wires. Hub spacers include steering wheel mounting hardware.
|
|
|
|
|
HS-003
Hub Spacer - Momo-Dino
|
|
Hub spacers are used when installing a steering wheel mounted trim switch. The spacers are drilled so the trim switch wiring can easily routed to the center of your hub. Rack and Pinion steering systems from Morse and Teleflex can be modified by gun drilling the shaft so the wiring can be routed through the center of the shaft to the back of the dash. When completed, the installation will be very clean with no exposed wires. Hub spacers include steering wheel mounting hardware.
|
|
|
|
|
HS-001
Hub Spacer - 9 Bolt Formula/Grant
|
|
Hub spacers are used when installing a steering wheel mounted trim switch. The spacers are drilled so the trim switch wiring can easily routed to the center of your hub. Rack and Pinion steering systems from Morse and Teleflex can be modified by gun drilling the shaft so the wiring can be routed through the center of the shaft to the back of the dash. When completed, the installation will be very clean with no exposed wires. Hub spacers include steering wheel mounting hardware.
|
|
|
|
|
|
|
|
|
|
|
|
|
SSD-R010
Steering Trim Switch - Dino (Right)
|
|
Switches designed to mount on the right side of the Dino wheel. They are made from billet aluminum and come polished, powder coated, or anodized. Steering shaft must be drilled for proper wiring.
|
|
|
|
|
SSD-L015
Steering Trim Switch - Dino (Left)
|
|
Switches designed to mount on the left side of the Dino wheel. They are made from billet aluminum and come polished, powder coated, or anodized. Steering shaft must be drilled for proper wiring.
|
|
|
|
|
SSD-D020
Steering Trim Switch - Dino (Dual)
|
|
Duel switches designed to mount on both sides of the Dino wheel. They are made of billet aluminum and come polished, powder coated, or anodized. Steering shaft must be drilled for proper wiring.
|
|
|
|
|
|
|
|
SSM-D020
Steering Trim Switch - Momo/Uflex (Dual)
|
|
Billet aluminum dual steering wheel switch for Momo steering wheels. Includes standard wire looms. If routing wires through the helm, also order the steering hub spacer for easy installation. Available in polished, powdercoated, and anodized finishes.
|
|
|
|
|
PL-1012
Place Diode Kit
|
|
|
This diode kit is required when adapting a 3 wire switch to a Place Diverter hydraulic pump. A common application would be installing a steering wheel trim switch to operate your Place Diverter. A wiring diagram is included and can also be viewed online in our instructions area.
|
|
|
|
|
DK-001
Twin Engine Diode Kit
|
|
|
|
This diode kit allows the usage of one trim switch to control two 12V operations. Commonly used for single trim switches to control two outdrives or two trim tabs with Oildyne trim pumps. A wiring diagram is included and can also be viewed online in our instructions area.
|
|
|
|
|
DK-002
Triple Engine Diode Kit
|
|
|
|
This diode kit allows the usage of one trim switch to control three 12V operations simultaneously. Commonly used for single trim switches to control three outdrives with Oildyne trim pumps. A wiring diagram is included and can also be viewed online in our instructions area.
|
|
|
|
|
|
DK-004
Bennett Single Switch Diode Kit
|
|
|
|
This diode kit enables the usage of a single switch to operate Bennett trim tabs or Dana Marine LT500 trim tabs simultaneously. A common application where this kit would be used in when installing a single steering wheel switch. The steering wheel switch and diode kit attach to the standard dual rocker switch on your dash. This enables you to control the tabs individually from the dash switch and simultaneously from the steering wheel switch. A wiring siagram is included and can also be viewed online in our instructions area.
|
|
|
|
|
|
DK-005
Bennett Dual Switch Diode Kit
|
|
|
|
This diode kit enables the usage of (2) SP/ST switches to operate Bennett trim tabs or Dana Marine LT500 trim tabs. A common application would be a dual steering wheel trim switch installation. The diode kit enables you to control the tabs individually from the steering wheel switches. A wiring diagram is included and can also be viewed online in our instructions area.
|
|
|
|
|
|
|
|
